Sensaphone

The Sensaphone Pressure Sensor can be used to measure and detect loss of pressure in many applications. An alarm from the pressure sensor can indicate a problem with a pump, a possible clogged influent line, loss of suction, a downstream clog or perhaps a burst pipe. Any of those failures can cause a pump motor to overheat and warp.

The Ethernet to WiFi Adapter is a high-speed, long-range outdoor wireless bridge that is an ideal solution for adding Wi-Fi connectivity to any network based Sensaphone. This is a cost effective solution when faced with running communication cable or trenching long runs of alarm wire to the Sensaphone.

SELF-POWERED infrared sensor that monitors the movement of warm bodies in a specific area. Will cause a dialout if motion is detected. The range is a maximum of 40 feet directly ahead of, and approximately 20 feet to either side of, the detector at 40 feet distance (see installation instructions for diagram).

50 ft. of shielded 22 gauge, 2 conductor, hookup wire used to connect sensors or thermostats to Sensaphone units or hardwired security systems.

Detects the presence of water on a horizontal surface. INDEPENDENTLY POWERED* by internal lithium batteries. Multiple sensors can be wired in series to a single input. Comes with 10' of hookup wire. (Additional wire available for purchase...see part number FGD-0010 or FGD-0010B). *It is essential that any water sensor used with the Sensaphone or a WisDom Wireless Universal Transmitter be self-powered.

The Temp Alert can be used with all Sensaphone models to monitor air temperature from 20 to 110 F (6.7 to 43.3 C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When the temperature exceeds the setting, the sensor triggers an alarm.

The Humidistat Humidity Switch can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic, a nylon sensing element provides long life and accurate humidity control.

The Zone Water Detector senses the presence of water via the attached WaterRope. The Zone Water Detector can be used with all models of Sensaphone. The sensor is a normally closed device. It operates on two (2) AA batteries (installed). The size of the monitored area can be extended by attaching additional lengths of WaterRope (FGD-0063) to the end of the included WaterRope.

10 foot length of WaterRope for the FGD-0056 Zone Water Detector. Up to ten (10) lengths of 10 foot rope (total length 100 feet) can be cascaded from a single Zone Water Detector. Dimensions: 10 feet long Compatible with the FGD-0056 Zone Water Detector.

The remote temperature sensor is designed to monitor air temperature indoors. It features terminal screw wiring connections, small size, and a convenient wall-mount housing.The sensor is accurate to +/- 1oF (0.56oC) and has a sensing range of -40oF to 175oF. Compatible with Sensaphone 400, Sensaphone 800, Sensaphone 1104, Sensaphone 1108, Sensaphone 1400, Sensaphone 1800, Sensaphone 2000, Sensaphone 2800, Sensaphone Express II, and Sensaphone Web 600.

The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits.

The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits.

The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits.

The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits.

The Sensaphone FGD-0102 10K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits.

The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated.

The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated.

The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated.

The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated.

The Sensaphone FGD-0104 10K Outdoor Air Weatherproof Temperature sensor is a sensitive temperature element with a stainless steel tube sheathe. It is mounted inside a ventilated, treated weather–resistant PVC shield to minimize radiant energy effects and mounted on a weatherproof outlet box for easy outdoor installation.